Comprising of 4 filtration stages as follows:

1. Stage one: Sediment removal via 9 3/4" 1 micron poly spun sediment cartridge http://urwater.com.au/products/Sediment-filter-9-3%7B47%7D4%22-Polypropylene-1-micron-cartridge-.html
2. Stage two: Chemical removal via 9 3/4" (248mm) Omnipure OMB934 1MPB cyst and lead reduction premium coconut carbon block. http://urwater.com.au/products/Omnipure-OMB934-1MPB-9-3%7B47%7D4%22-x-2.5%22-premium-coconut-carbon-block-filter-with-cyst-and-lead-reduction.html
3. Stage three: Reverse osmosis filtration via Genuine Dow Filmtec TFC membrane 300LPD
4. Stage four: Post carbon/ taste correction via Omnipure premium coconut carbon inline 2" x 10" filter cartridge. http://urwater.com.au/products/Omnipure-K2540-5M-Coconut-carbon-inline-filter-cartridge.html

Also includes the following as standard inclusions:

1. Large 15L Reverse Osmosis storage tank
2. Ceramic seated premium tap. http://urwater.com.au/products/%27Elegante%27-premium-tap-.html
3. Wells certified 600KPA Apex pressure limiting valve.
4. Stainless steel drain clamp (avoid self piercing drain clamps or plastic versions as they are usually non compliant with plumbing codes and increase your chances of leaks) 
5. Combination of Jaco and John Guest speedfit hose connections (top of the range fittings)
6. John Guest tubing (again, top of the range and less prone to kinking if bent)
7. US made 9 3/4" universal filter housings (not cheap Chinese copies). 9 3/4" systems allow you to purchase replacement filters from pretty much anywhere. Buyer beware of 9" systems. You'll find it harder to get replacement filters (we can source these) but you'll have a non standard filter and will pay more for every filter change than you should. Best bet is to stick to the standard size systems which are 9 3/4" which are sometimes referred to as 10" systems for some reason.
8. Powder coated steel mounting brackets. (Chinese metal brackets easily swell up in rust bubbles and make a hell of a mess under your kitchen sink)
9. Pressure gauge on Membrane pressure vessel inlet (Allows the user to monitor pressure drop which can be caused by blocked pre-filters) Reducing the pressure to the membrane will in turn lower your water quality. Higher water pressure = higher rejection rates)
10. Brass 1/2" Tee (meets Australian plumbing standards)
11. Brass 1/2" double nipples x 2 (meets Australian plumbing standards)
12. Chrome 1/4 turn cistern cock valve. (Wells certified)
13. Thread tape
14. Mounting screws
15. First set of filter cartridges
16. Reverse osmosis flushing valve (allows you to flush a higher volume of water though the waste line from your membrane to clean it which helps to maintain a higher quality of pure water)

System is assembled in our Brisbane workshop using quality US made parts and filters.

This system is not a cheap Chinese copy. Make sure the systems you look at are clearly stamped 'Made in USA'. The copies will look exactly the same except for this stamp.

Systems are available for order now and can be customised further to include remineralising cartridge to make it a 5 Stage system.

If you don't have the room under your kitchen sink that's not a problem. You can always remote the storage tank meters away in a hard to reach corner cupboard. There is a requirement when remoting the tank more than 2m to upgrade water lines from 1/4" tube to 3/8" tubing to maintain water pressure thoughout the system. Upgrade to 3/8" system is $25 extra. Please give us a call if you have any questions regarding an underbench system.

4 stage reverse osmosis system, underbench 4 stage reverse osmosis system, premium 4 stage reverse osmosis filtration system, fluoride removal system, undersink reverse osmosis filtration system